產品簡介

用變比電橋測量變壓器的變比，操作過程繁瑣、測量范圍狹窄，已經不適應現代測量快節奏、效率高的要求。為此，南澳電氣（武漢）有限公司采用現代電子技術，研制出了新一代全自動變比組別測試儀。它體積小，重量輕，精度高，穩定性好。它采用了大屏幕中英文液晶屏顯示、內置中英文菜單式操作，完成一組變壓器的測試只需11秒。NABZC全自動變比組別測試儀是電力工業部門的理想測試儀器。

產品別名

變壓器變比組別測試儀、變壓器雙臂電橋

產品特性

1．自動測量接線組別。

2．自動進行組別變換。

3．自動切換相序。

4．自動切換量程。

5．自動校表。

6．輸入標準變比后，能自動計算出相對誤差。

7. 一次測量完成，自動切斷試驗電壓 。

8. 設置數據,測量結果自動保存，可查看以前數據。

9. 測量有載變壓器,只輸入一次變比。

產品參數

1．變比測量范圍： 1—10000

2．組別：1—12點

3．精度: 1-1000 0.2 級 1000-10000 0.5級

4．電源：AC220V ±10%，50HZ

5．使用環境溫度：-5℃─ 40℃

6．使用環境濕度：＜85%

7．體積：430mm×320mm×215mm

8．重量：8Kg

注意事項

1. 保險1為2A,保險2為0.5A。如果測試線短路,高低壓接反,會熔斷保險。保險熔斷后，如果進行測量，在顯示“ 正在測量，請等待！”后停住。請關機，更換相同容量的保險，重測。

2.連線要保持接觸良好。儀器應良好接地！

3.儀器的工作場所應遠離強電場、強磁場、高頻設備。供電電源干擾越小越好，宜選用照明線,如果電源干擾還是較大，可以由交流凈化電源給儀器供電。交流凈化電源的容量大于200VA即可。

4.儀器工作時，如果出現液晶屏顯示紊亂，按所有按鍵均無響應，或者測量值與實際值相差很遠，請按復位鍵,或者關掉電源,再重新操作。

5.顯示器沒有字符顯示,或顏色很淡,請調節亮度電位器至合適位置。

亮度電位器是多圈電位器 ，有10圈！

6.儀器應存放在干燥通風處，如果長期不用或環境潮濕，使用前應加長預熱時間，去除潮氣。

7.通訊口調試時使用。

Productintroduction

When using this radiobridge to measure the transformer ratio, the operation procedure iscomplex, the measuring measure range is narrow, which is no longermeet modern fast-paced, high-efficiency re Therefore,NABZC electricaluses the modern electronic technology, developed a new generationof automatic variable ratio group tester. It is small, light, highaccuracy and with good stability. It uses a large-screen characterdisplay, menu operation, friendly interface. The variable group canmeasure at once. NABZC Automaticvariable ratio group tester is ideal product for electricalindustry department.

Alsocalled name

Transformer ratio group tester, transformer ratio tester,transformer ratio automatic tester, automatic transformer ratiotester, transformer ratio group testing device, transformer ratiotesting device, transformer ratio automatic testingdevice.

TheCharacteristics of the products

1. Automatic measurement wiring group.

2. Automatic group transformation.

3. Automatic switching phase sequence.

4. Automatic shift ranging.

5. Automatic calibration.

6. Input the standard ratio, it can automatically calculate therelative error.

7.When the measurement is completed, it can cut off the testingvoltage automatically .

8. Setting the data, the measured results can be savedautomatically, and can be view the previous data.

9. Measuring loaded transformer ratio, only need to enteronce

Theparameters of the products

1. Ratio measuring range: 1-10000

2. Group:1-12:00

3. Accuracy: 1-1000  0.2 grade,1000-10000 0.5 grade

4. Power supply: AC220V ±10%, 50HZ

5. Operating temperature: -5 ℃─ 40 ℃

6. Operating humidity:<85%

7. Volume: 430mm × 320mm × 215mm

8. Weight: 8Kg

Power supply: AC110V/115V/120V/127V/220V/230V/240Voptional

Input frequency: 50Hz/60Hz optional

Note: The users can select the corresponding power which based ontheir local supply voltage and frequency, and we will confirm itbefore the delivery (or inform us that the goods will be used inwhich country advance)

Attentionsshould take

1.Insurance 1 is 2A, Insurance 2 is 0.5A. If the testing line isshort-circuit , the high and low voltage will be reversed, willburn the fuse. Once fused, it will be displayed " measuring , wait! " and then stop to operate and cut off the power.Please replacethe same capacity insurance, then retesting .

2.Maintain the connections is fine. The instrument should be wellgrounded !

3.Ensure the workplace keep away from strong electric field ,magnetic field anduency devices. Power supplyinterference should be the smaller the better, and use light line.If the power supply interference is still large, it better to usethe AC purified power,.the purified AC power supply capacity justlarger than 200VA will do.

4.During the operating, if there is disorder on LCD screen, andwithout any response after press all the button, or the measuredvalue is much very far away from the actual value, please press thereset button, or turn off the power, then restart the operate.

5.If the displays without character display ,or the color is weak,please adjust the brightness potentiometer to the appropriatelocation . Brightness potentiometer is a multi-turn potentiometerwith 10 laps !

6.The instrument should be stored in dry and ventilated place , ifunused for a  long-term, or stored in a humid environment, itneed to extend the warm-up time before using , to remove  themoisture.

7.Communication port used for debugging .