Testitem 測試名稱: Fourwheel all-terrain vehicles (ATVs) is a revision of AmericanNational Standard 美國四輪ATV強制性安全標準
Testinfo 測試內容：
ANSI/SVIA 1 -2007 Section4.1.1(Service Brakes)
Functional: Frontbrakes must be operated by a lever on the right side of handle andoperable without removing hand from handlebarANSI/SVIA 1 -2007 Section 4.1.2(Service Brakes)
Functional:Operated by either a foot pedal near right footrest (right foot) orif no clutch lever,by a lever on the left handlebar and operablewithout removing hand from handlebarANSI/SVIA 1 -2007 Section4.1.3( Service Brakes)
Functional Test:Front and rear can be operated simtaneous by pedal - rightfootrest/right foot or by a lever on the left handlebar andoperable without removing hand from handlebarANSI/SVIA 1 -2007 Section 4.2(Parking Brakes)
Functional: AllMountain Bikes must have a parking brake *Mechanism will be tsetedaccording to section 8ANSI/SVIA 1- 2007 Section 4.4/4.4.1 / 4.4.2 (Engine Stop)
Functional: Musthave stop switch mounted on left handlebar and operableby thumb and must not require the operator to hold inthe off position to stop the engine , must be red ororangeANSI/SVIA 1- 2007 Section 4.5(Manual Clutch)
Funtional: Ifmanual clutch , it must have a clutch lever located on left side ofhandlebar and operable without removing hand fromhandlebarANSI/SVIA 1- 2007 Section 4.6(Additional Clutch Control)
Funtional: IfMountain Bike has power take off (PTO) or device for fixing enginespeed , it shall have a clutch control for the PTO locatedconvenient to the operator . Clutch direction of movementre/SVIA 1- 2007 Section 4.7 /4.7.2.1 - 4.7.2.4 (Throttle Control)
Functional: Musthave throttle control located on right side of the handlebaroperable without removing hand from handlebar . Various optionspossible for the configuration of throttle . Mountain Bike musthave means of stopping engine when operator dismounts. The PTO mustautomatically stop when operator is dimounted and must return tooperational mode when the transmission is placed ingear.ANSI/SVIA 1 - 2007 Section 4.81.1 - 4.82(Drive Train Control)
Functional: Ifmanual transmission, the gear shift control musr be located andoperable by operator left foot or left hand. Various options forfoot or hand operation and also labelingANSI/SVIA 1- 2007 Section4.9(Neutral lndicator)
Functional: Ifautomatic, neutral indicator must be readily visible to theoperator. The neutral indicator shall be activated whenever theignition system is on and the transmission is in neutral ANSI/SVIA 1 - 2007 Section4.10(Reverse lndicator)
Functional: Ifautomatic, the reverse indicator must be readily visible to theoperator.ANSI/SVIA 1- 2007 Section4.11(Electric Start Interlock)
Functional: Aninterlock shall be provided to prevent the Mountain Bike engineform being started by electric crankingANSI/SVIA 1- 2007 Section4.12(Passenger Handholds)
Functional:Type ⅡMountain Bike handholds must belocated on each side of passenger seating area. Handholds shall bedesigned to allow the passenger to dismount without interferencefrom the handholds
TEST:Type ⅡATVs Must withstand verticalforce of 1000 N (2241bf) applied statically to the center of thesurface of the hold at a maximumpressure of 1MPa (150psi)ANSI/SVIA 1 - 2007 Section4.13(Flag Pole Bracket)
Visual: Must have aflag pole bracket attached having a 12.7mm (0.5 in) dia mountingshaftANSI/SVIA - 2007 Section4.14(Manual Fuel Shuttoff Control)
Functional: If theMountain Bike has a manual fuel shutoff control ,it must meet 49CFRFMVSS 123 table 1 : Rotate to operate "On" and "Off" are saparatedby 90° of rotation. "Off" and "Reserve" (if provided) are separatedby 90° of rotation. Sequence order: On - Off -ReserveANSI/SVIA 1- 2007Section4.15(Handlebars)
Functional: Thehandlebars and its mounting shall present no ridged materials withan edge radius of less than 3.2 mm(0.125in) that may be contactedby a probe 165mm (6.5in) diameter sphere. The prode shall beintroduced to the handlebar mounting area. It shall not be possibleto touch any part of any edge that has a radius of less than 3.2mm(0.125in) with any part of the probe. Handlebar crossbar, ifprovided shall be padded.ANSI/SVIA 1 - 2007Section4.16(Foot Environment)
Functional:TypeⅠMountain Bike will havefoot rest. If foot pegs are present, the minimum separationdistance shod be of 200mm (8 in) center to centerANSI/SVIA 1 - 2007Section4.16.1.1 - 4.16.1.2 (Foot Probe Environment)
TEST: Apply a loadof 445N (1001bf) to the probe described in specification in avertical and downward position into region between the foot bar orpeg and the rear fender. The probe shod not contact the ground. Ahorizontal and rearward using 90N (20 ibf), shod not contact therear tire.ANSI/SVIA 1 - 2007 Section 4.17(Lighting)
Functional: AllMountain Bikes except Y, and may be included on Y must have atleast 1 headlamp and one tail lampANSI/SVIA 1- 2007 Section 4.17(Headlamp)
TEST: SAEJ1623-94
ALTERNATE TO TEST:The headlaamp manufacturer/supplier reports indicationg complianceto SAE specifications will be reviewed inleu oftesting.ANSI/SVIA 1 - 2007 Section 4.17(Tail Lamp)
TEST: SAEJ585-00
ALTERNATE TO TEST:The headlamp manufacturer/sopplier reports indicating compliance toSAE specifications will be reviewed inleu oftesting.ANSI/SVIA 1 - 2007 Section 4.17(Stop Lamp)
TEST:SAE J586-00 orJ278-95
ALTERNATE TO TEST:The headlamp manunfacturer/supplier reports indicating complianceto SAE specifications will be reviewed inleutesting.ANSI/SVIA 1 - 2007 Section 4.18(Spark Arresters)
Functional: Mustmeet one of US Dept of Agricture or Forest Service Standard forSpark Arrestors for Internal Combustion Engines 5100 -1 Sept 1997.Manf. Of spark arresters get Gov.approval.
ALTERNATE TO TEST:The headlamp manunfacturer/supplier reports indicating complianceto SAE specifications will be reviewed inleu oftesting.ANSI/SVIA 1 - 2007 Section 4.19- 4.19.2 (Tires/Tires Making/Tire pressure gauge)
Functional: All Mountain Bikes must bee with off-highway AT designated tires which follow the loadand presssure guidelines of Tire and Rim manufacturerassociation.Review marking re for tires. All MountainBikes must have a tires pressure gauge and a means of carryingit.ANSI/SVIA 1 - 2007 Section 4.20(Security)
Functional: AllMountain Bikes must have a means of being locked up, key operatedor e system with a minimum of 300 exclusive lockcombinations except Y Mountain BikesANSI/SVIA 1 - 2007 Section 4.21(Owners Manual and Owners Manuals Review)
Functional: AllMountain Bikes must be e with a owners manual and a means ofcarrying the manual safely.Readability and contents asspecified.ANSI/SVIA 1 - 2007 Section 4.22(ATV Identification Number)
Functional: Mustdisplay either a VIN number Title 49, CFR Part 565 or SAE ICS-1000Sept04 Off Road Vehicle Product Identification NumberingSystemANSI/SVIA 1 - 2007 Section4.23(Label Inspection)
Functional: ANSIZ535.4
ANSI/SVIA 1 - 2007 Section4.24(Hand tags)
Functional: Meetre of hang tag at point of saleANSI/SVIA 1 - 2007Section5.0(Maximum Speed Capability)
TEST: Tesr track -clean, dry smooth , level concrete or e
Must hitand maintain max speed for 100ft(30.5m)
Two test runs, inopposite direction.ANSI/SVIA 1 - 2007 Section 6.1/ 6.1- 6.4 (Maximum Speed Capability Measurement)
TEST: Category (Y)and (T) Mountain Bikes max speed re and speed limitingdevicesANSI/SVIA 1 - 2007 Section7.0/7.1 - 7.3 (Service Brake Performance)
TEST: Uses the sametest surface as section 5.0 and Mountain Bike conditions . Testmust be completed with an air temperature between 32 and 100F.After doing max speed, determine braking speed, burnish brakes ,and check the performance 6 times from 30mi/hr or brake test seedwhichever is lowerANSI/SVIA 1 - 2007 Section7.2(Service Brake Performance)
TEST: Determineforce required to press on brake handle or pedalANSI/SVIA 1 - 2007 Section 8.0-8.2(Parking Brake Performance)
TEST: Test surfacewith 30% grade, burnish brakes as above, park on grade facingdownward and apply service brake, repeat in uphill direction anddetermine the force required for parking brakeactuation.ANSI/SVIA 1 - 2007 Section9.0(Pitch Stability)
TEST:Document thedimensions of wheel base and weigh the front and rear of theMountain Bike. Perform calcations based on thatdataANSI/SVIA 1 - 2007 Section 10.0(EMC)
TEST: To Directive72/245/EEC as amended by Directive 95/54/EC or Directive 97/24/ECChapter 8ANSI/SVIA 1 - 2007 Section 11.0(Sound Level Measurement)
TEST: Appendix I-1to subpart D or part 205 Test Procedure for Street and Off-RoadMotorcycles. Procedure uses a microphones to take measurement.Mountain Bike must hit maximum speed again for approx 100ft. Seedetails in appendix of specification.ANSI/SVIA 1 - 2007 Section 12(Certification Label)
VISUAL:Re to placement, note, this wod only be applicable afterMountain Bike has passed all the tests
Samplesize 送樣規格：6pcs finishedproducts
Leadtime 測試周期: 常規 Regar 45working days
Others 其他信息：
Sample for reference參考圖片:
Sample Report報告樣本：
