購買油膠水膠兩用復合機請到江蘇鑫利龍來瞧瞧！

油膠水膠兩用復合機

 適用范圍：

水膠油膠兩用復合機（別名：雙漿槽網帶復合機、雙膠槽網帶復合機、雙漿輥網帶貼合機、雙膠槽網帶貼合機），適用于海綿、布類、EVA、人革、人造棉等材料的上膠貼合。主要用于制鞋、制帽、手套、皮衣、箱包、汽車座墊、玩具等行業的原料上膠貼合。

技術參數：

1、設備名稱：水膠油膠兩用網帶復合機

2、規格型號：XLL-2000mm

3、上膠方式：刮膠

4、烘筒規格：￠1500×2000（客戶可自定）

5、加熱方式：電加熱（蒸汽加熱或?qū)嵊图訜幔?/p>

6、電機功率：3KW+1.5KW/3HP+2HP

7、復合速度：0~35m/min

8、外形尺寸：8800mm×2650mm×2550mm(L×W×H)

設備特點：

1、可以給兩層材料同時上膠貼合，使復合牢度更好。也可用于給三層薄型材料一次性上膠貼合，提高生產效率，降低生產成本。

2、雙漿輥網帶復合機采用膠水作粘合劑，并用耐高溫網帶壓著，使復合材料與烘筒充分接觸，提高烘干效果，使加工后的材料柔軟、耐水洗、牢度好。

3、本機網帶具有自動紅外線調偏裝置，可以有效防止網帶跑偏，延長網帶的使用壽命。

4、本機的加熱系統分為兩組，用戶可以根據需要選擇加熱方式（一組或二組），可以有效節約能源，降低生產成本。

5、客戶可以根據需要選配直流電機或變頻器聯動，從而使機器具有更好的操控性。

操作要求：

操作者只有在完全熟悉，掌握機器的性能，工作原理后方可操作本設備。本設備必須有專人操作，非操作人員不能亂開，亂動。

生產前應檢查電纜、斷路器、接觸器、電機等電器是否符合要求。

生產前須檢查三相電源是否均衡，嚴禁缺相啟動設備。

生產期應檢查各旋轉接頭是否安全，管路是否暢通，有無破損，漏油，并及時排除。

生產前須將熱油機打開，待溫度升至工藝要求溫度后，方可生產。生產前應檢查各氣壓表壓力是否正常，氣路有無漏氣，并及時修復.

設備大批量生產前，應先做小量試驗，成功后方可大批生產。

生產前，應檢查各液壓站、減速機、軸承瓦盒、絲杠等潤滑情況，應正確及時的加注液壓油和潤滑油。

停機后，必須及時清洗膠槽及刮膠附件，網紋輥，清除機器各部分殘膠及污垢，以備下次使用。

Operational re:

Operators can operate the e only after they are fully familiar with the performance and working principle of the machine. The e must be operated by a special person, and non-operator can not be disorderly opened and disturbed.

Before production, electrical appliances such as cables, circuit breakers, contactors and motors should be inspected to meet the re.

Before production, it is necessary to check whether the three-phase power supply is balanced or not, and startup e without phase is strictly prohibited.

During the production period, it should check whether the rotary joints are safe, whether the pipeline is smooth, whether there is any damage, oil leakage, and timely removal.

The hot oil engine must be turned on before production, and can be produced only after the temperature is raised to the required temperature of the process. Before production, check whether the pressure of each barometer is normal, whether there is air leakage in the air passage, and repair it in time.

Before large-scale production of e, small-scale test should be done before large-scale production can be achieved.

Before production, the lubrication conditions of hydraulic stations, reducers, bearing bushes, screw, etc. should be checked, and the hydraulic oil and lubricating oil should be injected correctly and timely.

After shutdown, the rubber trough and scraper accessories, mesh rollers, residual glue and dirt in all parts of the machine must be cleaned in time for the next use.