RTP600W厚膜無感電阻0.1Ω-1MΩ-日本在線av視頻,閨蜜之間的小說
- 報價
- ￥10.00元每件
- 全國服務熱線
- 18948331417
- 微信號
- 13554875208
- 品牌
- 華鑫歐
- 型號
- RTP600W
- 產地
- 深圳市
RTP600W電阻 RTP無感電阻RTP厚膜電阻 RTP厚膜無感電阻
功率型 厚膜 無感電阻器 Power type Thickfilm Non inductiveResistor
l 底板中心溫度≤85℃ 額定功率250W～800W
l Base plate center temperature ≤ 85℃Rated power 250W～800W.
l 特殊設計的外型結構，芯片和外殼之間用彈簧聯接，用兩個螺絲固定安裝，能保證散熱片附著壓力在120 到 160 牛頓之間。
l The specially designed structuralshape connects the chip and the casing with springs and is securelymounted with two screws, ensuring that the pressure of the heatsinkattachment is between 120 and 160 Newtons.
l 搭配合適的散熱器使用時，功率可達到 2000W
l When used with a suitable radiator,the power can reach 2000W
主要應用于變速驅動器、供電、控制設備、通訊、自動控制、發動機控制等。適合逆變器電路、脈沖電路、高頻電路。
Mainlyused in variable speed drives, power supply, control e,communication, automatic control, engine control, etc. Suitable forinverter circuits, pulse circuits, and high-fre
降功率曲線斜率（熱阻）：RTP600:8.57W/K（0.12K/W）
額定功率
阻值范圍
阻值允許偏差
電阻溫度系數
Zui大工作電壓
耐電壓
Rated
Resistance
Resistance
Temperaturecoefficient
Maximumworking
Withstanding
power
range
Tolerance
（PPM/℃）
voltage
voltage
600W
0.5Ω-1MΩ
±1%、±5%、±10%
±150
5000VDC
6KV/Min
?2025V1.0
RTP600
試驗項目
試驗條件
性能指標
Test items
Experimentalconditions
Performance indicators
溫度快速變化
-55℃～+155℃，經五次循環；極限溫度暴露時間：
電阻器應無可見損傷且標志清楚
30 分鐘；轉換時間：1～2分鐘
The resistorshould have no visible
Rapidtemperature
-55℃ to+155℃, after fivecycles; Extreme temperature
damage andclear markings,
changes
exposure time:30 minutes; Conversion time: 1-2 minutes
△R≤±（0.5%R+0.05Ω）
溫度系數
TCR 在±150X10-6/K之內
Temperature
25℃～105℃
TCR within ± 150X10-6/K
coefficient
正常氣候條件下，在電阻器的金屬散熱板與引出端之間
測試絕緣電阻，試驗電壓（直流）為500±5V
絕緣電阻應≥10GΩ
絕緣電阻
Under normalweather conditions, test the insulation
The insulation resistance should be
Insulation resistance
resistancebetween the metal heat dissipation plate of the
≥10GΩ
resistor andthe lead out terminal, with a test voltage (DC)
of 500 ±5V
施加額定功率 2倍的直流電壓（Us≤1.5Umax）
電阻器應無可見損傷且標志清楚
過載
時間為5秒
The resistorshould have no visible
Overload
Apply a DCvoltage of twice the rated power
damage andclear markings,
(Us ≤ 1.5 Umax)for 5 seconds
△R≤±（0.5%R+0.05Ω）
穩態濕熱
電阻器應無可見損傷且標志清楚
溫度：40±2℃；濕度95%；時間：56 天
The resistorshould have no visible
Damp heatsteady
Temperature: 40± 2 ℃; Humidity of95%; Time: 56 days
damage andclear markings,
state
△R≤±（0.5%R+0.05Ω）
施加電壓：額定功率直流電壓（UR≤U max）
電阻器應無可見損傷且標志清楚
壽命
1.5 小時通電，0.5小時斷電，總時長 1000 小時
The resistorshould have no visible
Life
Appliedvoltage: rated power DC voltage (UR ≤ U max),
damage andclear markings,
powered on for1.5 hours, powered off for 0.5 hours, total
△R≤±（0.5%R+0.05Ω）
duration 1000hours
電阻器無擊穿或飛弧現象，漏電流
耐電壓
施加交流有效值電壓 6KV，時間為1 分鐘±5 秒
≤10mA
Withstanding
Apply aneffective AC voltage of 6KV for 1 minute ± 5
The resistorhas no breakdown or
voltage
seconds
arcingphenomenon, and the
leakage currentis ≤ 10mA
按 GB/T2423.10-2019要求進行試驗，振動頻率為
10Hz,振幅 0.35mm，加速度50m/s2,每個方向 2 次掃頻，
電阻器塑封體應無機械損傷，阻值
振動
3 個方向，每個方向持續時間 23分鐘
變化在±2%R+0.05Ω之內
Vibrate
Conduct thetest according to the re of
The plasticcasing of the resistor
GB/T2423.10-2019, with a vibration frequency of 10Hz,
should have no mechanical
amplitude of0.35mm, acceleration of 50m/s 2, 2 frequency
damage, and the resistance change
scans in each direction, 3 directions, and a duration of 23
should bewithin ± 2% R+0.05 Ω
minutes in each direction
?2025V1.0
RTP600
功率型 厚膜 無感電阻器 Power type Thickfilm Non inductiveResistor
產品類型
功率
阻值
精度
Product type
Power
Resistance
Accuracy
3R9=3.9Ω
F：±1%
RTP
600 Watts
10R=10Ω
J： ±5%
20K=20KΩ
K： ±10%
l 電阻器通過螺絲安裝在散熱器上，螺絲安裝扭矩為2N.m，應確保產品安裝緊固，無晃動。另外應為螺絲配套防松組件，如：平墊、彈墊、防松螺母等。
l The resistor is installed on the heat sink with screws, and theinstallation torque of the screws is 2N. m. It should be ensuredthat the product is installed firmly without shaking. In addition,screws should be e with anti loosening components such asflat washers, spring washers, anti loosening nuts, etc.
l 電阻器引出端電氣安裝使用的是 M5螺絲，螺絲安裝扭矩為1.3N.m，應確保電氣連接緊固，無晃動。另外應為螺絲配套防松組件，如：平墊、彈墊等，防止振動造成電氣連接松脫。
l M5 screws are used for the electrical installation of the resistorlead out end, with a torque of 1.3N. m. It should be ensured thatthe electrical connection is tight and there is no shaking. Inaddition, screws should be e with anti loosening components,such as flat washers, spring washers, etc., to prevent electricalconnections from loosening due to vibration.
l 電阻器與安裝面之間需要均勻的涂覆一層導熱硅脂，推薦使用導熱系數1W/mK的導熱硅脂產品。
l A uniform layer of thermal grease should be applied between theresistor and the installation surface. It is recommended to usethermal grease products with a thermal conductivity of1W/mK.
l 產品在貯存期間，應貯存在環境溫度為-10℃～+45℃，相對濕度不大于85%，通風、干燥、周圍無酸堿或其他有害物質的倉庫內。
l During storage,the product should be stored in a warehouse with an ambienttemperature of -10 ℃ to+45℃, a relativehumidity of no more than 85%, ventilation, dryness, and no acidic,alkaline, or other harmful substances around it
RTP600W電阻 , RTP無感電阻 , RTP厚膜電阻 , 厚膜無感電阻 , 厚膜無感電阻圖片
保險絲電阻，繞線電阻，無感電阻，高壓電阻，高精密電阻，水泥電阻，鋁殼電阻，大功率瓷管可調電阻，模壓電阻
一般經營項目是:電子元件、電阻器、電子產品的技術研發與銷售;國內貿易;貨物及技術進出口。（法律、行政法規、國務院決定規定在登記前須經批準的項目除外; 依法須經批準的項目,經相關部門批準后方可開展經營活動。）,許可經營項目是:無。深圳市華鑫歐電子有限公司目前的經營狀態為存續（在營、開業、在冊）。
深圳市華鑫歐電子有限公司是從事各類元器件、電子材料、電子專用設備的設計、研發、生產和經營的企業。公司主要產品有：傳統插件色環電阻器、模壓型電阻器、精密采樣電阻器、精密電阻器、精密電阻網絡、線繞電阻器、功率型鋁外殼電阻器、功率型水泥瓷殼電阻器、低阻電阻器、分流器等。產品廣泛應用于、交通、鐵路、電氣、廣播通訊、儀器儀表、家用電器、電力機車、電力電源等領域。公司自成立以來，致力于電子元器件的研制、開發、生產和銷售。公司擁有先...