立式攪拌機

Vertical Mixer

特點：

Features :

占地少，容量大，耗電低，省人工，混合均化快捷

It occupies less space, has large capacity, low power consumption, labor saving and uniform mixing

自動運轉計時，馬達過載保護，加料限位報警（選配）

Automatic operation time, motor overload protection, feeding limit alarm (optional)

設備與原料所接觸部分的材料均為不銹鋼制作，清料容易不易生銹

The materials in the parts in contact with the raw materials are made of stainless steel, and the materials are easy to rust

日本NSK軸承，采用內置式或分離式安裝方式，使原料或粉末與軸承分離，不易卡死，大大延長軸承使用壽命

Japan NSK Bearings, using built-in or separate installation, so that the separation of raw materials or powder and bearings, is not easy to get stuck, greatly extend bearing life

工作原理：立式攪拌機的工作原理是螺桿的快速旋轉將原料從桶體底部由中心提升至頂端，再以傘狀飛拋散落，回至底部，這樣原料在桶內上下翻滾攪拌，短時間內即可將大量原料均化的混合完畢

Working principle : The working principle of the vertical mixer is that the rapid rotation of the screw raises the material from the bottom of the barrel from the center to the top. And then throw the material in a manner of umbrella shape to the bottom. The materials are mixed up and down in the bucket in a short time

用途：塑料片料、粉碎料、塑料粒料、塑膠新舊料及添加色母攪拌均化等用途

Use : Plastic materials, regrind, plastic pellets, plastic masterbatch mixing old and new materials are added and so on purpose

適用行業：切粒、塑膠造粒、色母制造、塑料改性、再生料回收加工、大件注塑等行業

Applicable industry : Cutting, plastic granulation, color masterbatch manufacturing, plastic modification, recycled material recycling processing, large-scale injection molding and other industries

立式加熱攪拌機

Vertical Heating Mixer Series

特點：

Features :

攪拌干燥同步：由于物料在進行干燥過程中，持續保持流動狀態。熱量滲透均化。干燥時間短且不易結塊。

Stirring and drying synchronization : Since the material is kept in a flowing state during the drying process, the heat is uniformly penetrated, the drying time is short, and it is not easy to agglomerate

本系列標準機型為：雙層桶體設計（經濟型為單層設計）內層與物料接觸部分全部為不銹鋼材料制造，中央夾層安裝特殊保溫材料，因而可達到安全、節能的效果

The standard models of this series are : double-drum design(economical single-layer design), the inner layer and material contact parts are all made of non-induced steel materials; the middle interlayer is e with special insulation materials, which can achieve safety and energy saving effect

特制高頻加熱器，加熱快，耗電少，每頓料干燥綜合成本為25-30元，（含水1%以下，PP造粒料測試，0.9元/度電費計算，使用ABT-10R型測試

Specialuency heater, fast heating, low power consumption, the comprehensive cost of drying each material is 25-30 yuan. (Aqueous 1% or less, PP granulation test, yuan /kwh electricity cost calculation, using ABT-10R type test)

特設雙管排濕口，能有效排出濕氣，收集粉塵，絕不污染工作環境

The special double-tube drainage port can effectively discharge moisture, collect dust, and never pollute the working environment

桶體設有入口門（選購）換色換料清理簡單快捷

The barrel body is provided with an entrance door (optional), and it is quick and easy to change color and refuel

型號多，容量大，常備一次性能裝載：0.5噸、1噸、1.5噸、2噸、3噸等現貨供客選用

There are many models and large capacity, and one performance load is available: 0.5 tons, 1 ton, 1.5 tons, 2 tons, 3 tons, etc

干燥混合功能二合一，當不需要干燥時，只需將“加熱開關”及“風機開關”關閉，本系列機型即可用于塑料攪拌均化用途，一機二用。

The dry mixing function is two-in-one, When it is not necessary to dry, just turn off the “heating swich” and “fan switch” . This series of models can be used for plastic mixing and homogenization purposes, one machine and two